Top wood splitting tools

The Easiest Way to Split Wood: Top 5 Wood Splitting Tools

For one to create a long-lasting and hot fire, wood is an essential factor. Splitting wood is vital as it allows penetration of air in the wood and drying up as well. The aim of splitting the wood is to reduce the weight a log carries and making it easier to handle and stack them. However, splitting the wood can be a difficult task, especially when not using the right splitting tools. Besides having the required tools, it is vital to ensure you have insights on how to use them to avoid injuries during the operations.

That’s not all what AtlanticWoodworking.com know

Top 5 wood splitting tools

The following are tools that will help you to split the wood effectively successfully:

  • Axe and Splitting maul
axe splitting wood

The axe and the splitting maul are two different handy tools that look similar in some aspects. Axes have been in use for a long time, and the traditional method of splitting wood is still in use today. Axes and mauls are an excellent form of exercise besides their work, and not everyone will go for them, especially with bulky work. Using these hand tools requires physical ability, time, and inclination.

Today, the axe and the maul come in various head and handle designs. An axe is light in weight but requires immense strength to wield and ideal for small logs. The splitting maul is much thicker than the axe and is also blunt and heavy. It is ideal for splitting heavy and hardwood along the grain. A sledgehammer edge at the back comes in handy making it easier to split the wood.

  • Splitting wedges
Splitting wedges

The wedges are best known to deal with knotty pieces with ease. Wedges work better when there is a combination of a sharp started wedge and other blunt and wider wedges. The starter wedge is used to bite into the wood while the blunter and wider wedge continues with the started job. The wedges are driven into the wood using a sledge. The advantage is that it is driven in the same spot until the wood splits.

  • Hydraulic log splitter
Hydraulic log splitter

Hydraulic log splitters have the capabilities of splitting bulky firewood with ease whether it is softwood or hardwood. It is also able to deal with knots efficiently. They are available in three models: electric, manual, and gas hydraulic log splitter. The electric hydraulic log splitter is electric-powered, making it easier to split the wood by just pressing the buttons once the logs are loaded.

The manual one uses hydraulics and has two handles that extend upward. Cutting using the manual hydraulic is done by placing the wood between the hydraulic extension and the wedge and pulling the handles each at a time. It helps to push the arm towards the log facilitating the splitting of the woods.

The gas hydraulic log splitters are ideal for splitting any wood given the tons of force they produce. They can also be used anywhere since they are run using gas. They have a wedge which means with an X shaped wedge, you can save a lot of time by splitting the pieces into four.

  • Chainsaws
Chainsaws

The chainsaws can be used to split firewood with ease. They are available in either corded, Electric or gas chainsaws. They have multiple functions from the felling of trees, pruning, limbing as well as splitting the logs. Given their features, high performance, and power, they give maximum value and does a perfect job.

It is essential to understand that when using a chainsaw, caution should be taken and also, having insights is very important. It can be difficult for beginners to do a perfect job when using the chainsaw. The chainsaws are however very convenient and safe as long as the correct procedure is followed and safety gear put in place.

  • Crosscut saw
Crosscut saw

The crosscut saw is another vital tool that helps to split wood. It is similar to a handsaw given its handle. The crosscut saws have a heavy and stiff blade which makes them suitable for tasks such as turning the already felled trees into logs and firewood. Their lightweight makes them flexible, easing the operations. 

They have teeth patterns which are intended to cater for different cuttings. It is easy to use the crosscut saw as it resembles the handsaw which operates similarly. It is ideal for beginners and amateurs.

Conclusion

Splitting the wood is essential as it paves the way for good heating using well dried and aired firewood. There are various wood splitting tools available, and all are dependent on the needs and preferences of the users. The tools mentioned above are ideal for splitting as they are efficient and offer convenience. It is wise to ensure all the safety gears are in place and following the right procedure when using the tools.

Other posts:

How to Cut a Large Log on the Ground

How to Cut a Large Log on the Ground

How to Cut a Large Log on the Ground

Cutting large logs on the ground is an easy task when the right procedure is followed. Having information and experience on how to do it helps in saving time. It also assists in avoiding hurting oneself and those around. First of all, it is essential to get the right tools, and for the large logs, chainsaws are the best deal.

As far as AtlanticWoodworking.com know, It is ideal to pay attention to the characteristics of the log as it helps in the entire cutting process. Also, safety comes first. The cutters should always ensure they have the protective gears from the safety glasses, heavy boots, earplugs, and gloves.

How to Cut a Large Log on the Ground

Read also:

How to Make a Sawmill with a Chainsaw

How Do I Stop My Chainsaw From Pinching?

Things to do before cutting the large logs

  • First, choosing the tools and accessories to be used is essential. Also, the working condition of the chainsaw should be verified to ensure it is viable for the job.
  • The area should be well cleared of any debris to ensure that there is enough working space.
  • A great posture should be in mind as it comes with less fatigue. The upper body should be in a position where it supports the chainsaw without issues. To achieve this, the distance between the feet (feet apart) should be more significant than the length of the shoulders.

The procedure of cutting the large logs on the ground

When the log is on a ground level, two cutting methods can be used; over bucking and under bucking. Over bucking refers to when the log is cut from the top. It is the simplest yet the safest way to cut a log on the ground. Under bucking refers to when the log is cut upwards from the lower side.

Cutting a log from the ground can be challenging due to the fact that the chainsaw can run on into the earth if not handled carefully. Either way, suspending the tree on one side is not an option as it causes more problems. With a well-leveled ground, safety precautions, and a good posture in place, the operation is deemed to be a success.

The ground should be firm, to ensure the logs will not roll. To ensure stability, one can use small pieces of wood or wedges where necessary.

The procedure of cutting the large logs on the ground

Steps to be followed

  • Start the chainsaw at a low speed. It should be well-positioned at the pre-market points on the log.
  • The next step is sawing about three-quarters of the log and stop. It helps prevent the chainsaw from touching or cutting the ground.
  • The above procedure should be repeated on all the pre-marked points on the log.
  • Once all the marked points are cut three-quarter way, the logs should be rotated at 180 degrees. A felling level can be used where necessary. The logs should be held firmly in the ground as well.
  • The final step is finishing the cuttings that were left on three quarters from the opposite side.

The dos and don’ts when cutting a log on the ground

  1. Cutting the log from top to bottom while applying light pressure on the saw. Also, it is crucial to let the saw work itself, allowing the teeth to pull the chain bar into the log being cut.
  2. The guide bar nose should not come in contact with the ground or any other object.
  3. In the case of chainsaw pinching, one should not restart the chainsaw when it is still pinched.

What to do when the chainsaw is pinched during cutting of large logs

Sometimes, minor issues occur when cutting large logs on the ground and should be addressed and continue with the process. If the guide bar is pinched or caught in the log, forcing it out is not an option. One should turn the chainsaw off and drive a wooden wedge or plastic into the cut using a hammer. It helps in removing the saw with ease.

One should avoid restarting the chainsaw before solving the pinching problem. Once the pinching is resolved, the chainsaw can be restarted and continue with the operation using the same downward direction of cutting the log.

Conclusion

Cutting large logs on the ground is an easy task when the right procedure is followed. Having the right tools and a clear area also comes in handy. Precautions and safety measures should also be taken into consideration as well as things to do in case problems arises during the operations. The above method, as explained, is the simplest method which ensures the cutting of large logs is successful.  

How to Make a Sawmill with a Chainsaw

How to Make a Sawmill with a Chainsaw

In this day and age, most people normally take any type of wooden products for granted.  However, no matter where you go, you can see how wood has influenced your life in some way shape or form.  In fact, wood is sitting just behind the walls of your home helping hold your house up and keeping the roof from caving in on you. 

You walk around on wooden floors, use wooden handrails to get up and down the stairs, and love looking at exposing beams and other millwork.  The artwork is even displayed using wooden frames.  Yet almost nobody takes a second to stop and wonder how all of this woodwork was produced in sawmill.

What Exactly Is A Sawmill?

When you hear the term sawmill, you may think to yourself that you have no clue what that is.  If this is the case, you have nothing to worry about, as many people have no idea what a sawmill really is.  When it comes to the word sawmill, there are actually two different definitions. 

  • The first definition is going to be defined as a place where there is lumber milling taking place.  It will include any and all parts of the lumber milling process.  This includes the log yard where the logs are sorted out, where the milling machines are housed, and even the sorting out and storage of the cut wood.
  • The second definition is an actual cutting or sawing machine that is going to take a round log and turn it into square pieces of timber.
Make Sawmill with a Chainsaw

With both of the definitions out of the way, let’s agree that the definition of a sawmill is a system of turning logs or larger pieces of wood into smaller pieces of lumber.

Now you may be wondering how a sawmill relates to a sawmill with a chainsaw and how you can build one.  Since you now know what a sawmill is, a chainsaw mill is the same exact thing, the only difference being that you are going to be using a chainsaw to cut the wood into the smaller pieces of lumber.

How To Make A Saw Mill With A Chainsaw

One of the many reasons for why you may want to build a sawmill with a chainsaw is because it is a relatively portable and cheap way to take bigger logs and other pieces of wood, and create some very beautiful planks out of them.

Here is exactly how you are going to make a sawmill with a chainsaw:

  • Step #1:  The Concept

The concept of a chainsaw mill, also referred to as an Alaskan mill, is very simple.  You are going to start by using a straight reference edge that is placed on top of the log that you wish to turn into planks (an example of a straight reference edge is going to be a ladder).  Your chainsaw mill is going to be the jig that is attached (and that you are going to build), and will hold the chainsaw in alignment with your straight reference edge.  This will allow you to cut a very straight edge.  After you have the first flat surface cut, you can then switch to using that as your straight reference edge instead of your ladder.

  • Step #2:  User Safety

There is no hiding the fact that using a chainsaw in general is going to be very dangerous.  So before you even attempt to make your own sawmill with a chainsaw, be sure that you are experienced in using a chainsaw.  And as with any time you are using a chainsaw, be sure that you are wearing the proper protective equipment to help keep you safe and protected from any accidents.  Once you have all of your safety gear, you are now ready to get stared on your sawmill.

  • Step #3:  Get Your Parts For The Sawmill Ready

If you are going to build a sawmill, it is recommended that you use aluminum as it will last much longer, won’t rust, and will be much easier to transport and adjust.  To get what you need, you are going to want to visit your local hardware store or order the aluminum online.  Once you have your aluminum, here are the lengths you will need to cut, or you can simply order these lengths initially.

  • 2 x 900 mm:  These will be the long rails (A)
  • 4 x 400 mm:  These are for the inner bracings (B)
  • 2 x 500 mm:  These are the verticals (C)
  • 2 x 100 mm:  These are the small vertical pieces (D)
  • one 900 mm long with t-slot (40 mm x 16 mm) (E)

Once you have all of your pieces cut to length, you are ready to start building your sawmill.

  • Step #4:  Tap The Threads

You are going to want to tap some M8 threads into both ends of the inner braces (B), as well as one of the ends of the verticals (C) and smaller verticals (D) too.

  • Step #5:  Drill Clearance Key Holes

Once all of your holes have been tapped, you can know make 90 degrees butt joints.  However, in order to use M8 flange bolts, you must first drill a 7 mm hole so that the allen/hex key will have clearance.

  • Step #6:  Assemble Your Sawmill

Now you can assemble your sawmill.  For this part, it is best to use a diagram that you can easily find online, as this will be the best way to get your sawmill assembled without making any major mistakes.  However, if you know what you are doing, no diagram will be required and you can get your sawmill assembled much quicker.

  • Step #7:  Drilling The Guide Bar

Once your sawmill is assembled, you are going to need someway for attaching your chainsaw’s guide bar.  For this, you are going to want to attach the guide bar to the verticals ©.

  • Step #8:  Mounting The Guide Bar

Once your have your guide bar placement perfectly mapped out, you can drill any clearance holes and bolt on the chainsaw’s guide bar.  For this, it is recommended that you use locktite to prevent the bolts from rattling loose.

Making a Sawmill By a Chainsaw

After this final step is done, you will have successfully built a sawmill with a chainsaw.  Just remember to be careful whenever you are using a chainsaw in general, and with your new sawmill until you are familiar and comfortable with it.

We are AtlanticWoodworking.com! Thanks for reading